Difference between revisions of "Installing OpenOCD"
From spiderboard.org
(Created page with "= From APT = If your distributor provides OpenOCD (version 0.10 or higher, with ftdi-usb-blaster interface) it is sufficient to run in a terminal: : $ sudo apt install openoc...") |
|||
| Line 1: | Line 1: | ||
| − | = | + | == Installing OpenOCD == |
| − | If your distributor provides | + | * OpenOCD Version >= 0.10 with the libftdi driver is required. |
| − | : $ sudo apt install openocd | + | * If your package distributor provides this version, use your package manager to install OpenOCD: |
| + | * For Debian based distributions the terminal command is: | ||
| + | *: '''$''' sudo apt install openocd | ||
| + | * If the package version does not work, it is possible to compile OpenOCD from [https://github.com/ntfreak/openocd source]. | ||
| − | + | == Shell Script For Easier Use == | |
| − | + | A shell script can be used that starts OpenOCD, runs the svf file and shuts down afterwards, allowing conveniently programming the FPGA using a single terminal command. | |
| − | |||
| − | = | + | * Create the file '''mx10spider_prog''' under ''.local/bin'' in your home directory and insert the content below. |
| + | * If not already done, add ''.local/bin'' to the path variable. | ||
| + | ** Open .profile in your home directory with a text editor and add the line: | ||
| + | **: PATH=".local/bin:$PATH" | ||
| + | * Open a terminal and add the executable flag. | ||
| + | *: '''$''' chmod +x .local/bin/mx10spider_prog | ||
| + | * You are now ready to progrmm the fpga using the command: | ||
| + | *: '''$''' mx10spider_prog ''<path/to/file.svf>'' | ||
| − | + | <br> | |
| + | |||
| + | '''mx10spider_prog:''' | ||
| + | <nowiki> | ||
| + | #!/bin/sh | ||
| + | |||
| + | me=$(basename $0) | ||
| + | |||
| + | if [ -f "$1" ]; then | ||
| + | |||
| + | openocd -c "interface usb_blaster" -c "usb_blaster_lowlevel_driver ftdi" -c "usb_blaster_vid_pid 0x04d8 0xefd0" -c "jtag newtap max10 tap -irlen 10 -expected-id 0x31810dd -expected-id 0x318a0dd \ | ||
| + | -expected-id 0x31820dd -expected-id 0x31830dd -expected-id 0x31840dd \ | ||
| + | -expected-id 0x318d0dd -expected-id 0x31850dd -expected-id 0x31010dd \ | ||
| + | -expected-id 0x310a0dd -expected-id 0x31020dd -expected-id 0x31030dd \ | ||
| + | -expected-id 0x31040dd -expected-id 0x310d0dd -expected-id 0x31050dd" -c "init" -c "svf $1 progress" -c "shutdown" | ||
| + | |||
| + | elif [ "$1" = "" ]; then | ||
| + | |||
| + | echo "\tError: No file specified.\n\tUsage: $me <file.svf>" | ||
| + | |||
| + | elif [ "$1" = "-h" ] || [ "$1" = "--help" ]; then | ||
| + | |||
| + | echo "\tUtility script to start openocd and run an svf file.\n\tUsage: $me <file.svf>" | ||
| + | |||
| + | else | ||
| + | |||
| + | echo "\tFile not found: $1\n\tUsage: $me <file.svf>" | ||
| + | |||
| + | fi | ||
| + | </nowiki> | ||
Revision as of 12:34, 21 May 2019
Installing OpenOCD
- OpenOCD Version >= 0.10 with the libftdi driver is required.
- If your package distributor provides this version, use your package manager to install OpenOCD:
- For Debian based distributions the terminal command is:
- $ sudo apt install openocd
- If the package version does not work, it is possible to compile OpenOCD from source.
Shell Script For Easier Use
A shell script can be used that starts OpenOCD, runs the svf file and shuts down afterwards, allowing conveniently programming the FPGA using a single terminal command.
- Create the file mx10spider_prog under .local/bin in your home directory and insert the content below.
- If not already done, add .local/bin to the path variable.
- Open .profile in your home directory with a text editor and add the line:
- PATH=".local/bin:$PATH"
- Open .profile in your home directory with a text editor and add the line:
- Open a terminal and add the executable flag.
- $ chmod +x .local/bin/mx10spider_prog
- You are now ready to progrmm the fpga using the command:
- $ mx10spider_prog <path/to/file.svf>
mx10spider_prog:
#!/bin/sh
me=$(basename $0)
if [ -f "$1" ]; then
openocd -c "interface usb_blaster" -c "usb_blaster_lowlevel_driver ftdi" -c "usb_blaster_vid_pid 0x04d8 0xefd0" -c "jtag newtap max10 tap -irlen 10 -expected-id 0x31810dd -expected-id 0x318a0dd \
-expected-id 0x31820dd -expected-id 0x31830dd -expected-id 0x31840dd \
-expected-id 0x318d0dd -expected-id 0x31850dd -expected-id 0x31010dd \
-expected-id 0x310a0dd -expected-id 0x31020dd -expected-id 0x31030dd \
-expected-id 0x31040dd -expected-id 0x310d0dd -expected-id 0x31050dd" -c "init" -c "svf $1 progress" -c "shutdown"
elif [ "$1" = "" ]; then
echo "\tError: No file specified.\n\tUsage: $me <file.svf>"
elif [ "$1" = "-h" ] || [ "$1" = "--help" ]; then
echo "\tUtility script to start openocd and run an svf file.\n\tUsage: $me <file.svf>"
else
echo "\tFile not found: $1\n\tUsage: $me <file.svf>"
fi
